Installation of gas stoves for decoration and lite

2022-07-22
  • Detail

Gas stoves are kitchen appliances with high utilization rate and high safety requirements in daily life. Sometimes we buy a gas stove from the Internet, but we don't know how to install it. In fact, the installation of the gas stove is quite simple, and the slightly difficult thing may be to adjust the fire. If your kitchen has just been decorated, you are also going to use the embedded gas stove, and the stove hasn't been perforated yet. At this time, after you choose a gas stove, you must make holes on the stove according to the hole size prompted by this stove, so as to ensure the smooth installation of the gas stove

the installation of gas stoves is something we should consider when decorating the kitchen. In addition, the size of gas stoves also affects the size of holes in the cabinet panel. Therefore, when installing cabinets, it is necessary to determine the type and specific model of gas stoves. Only in this way can the subsequent installation become smooth. In addition, if you can't install the gas stove, please ask a professional master to operate it, so as to avoid danger caused by improper operation

meaning of gas stove installation

gas stove is a kitchen appliance with high utilization rate in daily life and high safety requirements. Sometimes we buy a gas stove from the Internet, but we don't know how to install it. In fact, the installation of the gas stove is quite simple, and the slightly difficult thing may be to adjust the fire. If your kitchen has just been decorated, you are also going to use the embedded gas stove, and the stove hasn't been perforated yet. At this time, after you choose a gas stove, you must make holes on the stove according to the hole size prompted by this stove, so as to ensure the smooth installation of the gas stove

installation process of gas stoves

step 1: install gas pipes

before installing the gas pipe, we need to put the stove into the stove with holes in advance, as shown in the figure below

step 2: clean the gas inlet of the stove, put the rubber hose joint into the stove joint and exceed the red line (see the figure below), and clamp the rubber hose with a pipe clamp or hoop

step 3: check whether the battery box has batteries. If not, please purchase and install batteries, generally No. 1 batteries

now that the basic installation is completed, you start to open the knob to test whether there is a fire, or to see whether the flame color is light blue. If the flame color is yellow or red, you need to debug the gas stove

step 4: debug the gas stove to make its flame show normal color, that is, light blue, as shown in the figure below

precautions for the installation of gas stoves

after the purchase of gas stoves home, you need to pay attention to the precautions before installation

first, please carefully check whether the product accessories are complete and damaged according to the packing list after unpacking. If any problem is found, please contact the dealer for replacement

second, please check whether the type of gas you use is consistent with the type of gas marked on this product. If it is inconsistent, it is strictly prohibited to install and use it (the type of gas is marked on the nameplate and outer package of the bottom shell of this product)

third, check whether all parts of the product are installed correctly and whether the screws are fastened, so as to avoid possible damage during transportation and affect the use of the product. After checking that there is no problem, we began the installation work

fourth, generally speaking, the clear distance between the back of the stove and the wall is not less than 15cm, and the clear distance between the side and the wall is not less than 20cm; If the wall is made of inflammable materials, a thermal insulation and fire-proof layer must be pasted. The excess part of the fire-proof layer beyond both ends of the stove and below the stove shall not be less than 10cm, and the excess part above the stove shall not be less than 80cm; The minimum distance between the cooker and the steel cylinder is 1m, and the longest air inlet hose should not exceed 2m

fifth, the stove should be installed in a well ventilated kitchen. Do not stack inflammables under and around the stove, which is easy to cause fire hazards; The kitchen area should not be less than 2 square meters, and the indoor height should not be less than 2.2m; The kitchen should be well isolated from adjacent rooms to prevent mutual collusion of leaked gas

sixth, the installation of desktop and integrated stoves is relatively simple, and the installation of embedded stoves is more complex. When the embedded installation is selected, the holes must be opened in strict accordance with the requirements of the installation position and opening size in the manual. When there are flammable materials around the installation position of the stove, the heat insulation and fire protection board must be used; The size of the opening is appropriate, which can not cause the table to squeeze the whole machine or make the panel bear the gravity of the stove body, especially the glass panel stove; When installing the cooker, pay attention that the four corners of the cooker panel should not be impacted by hard objects

acceptance of gas stove installation

first, the fire outside in the above figure is called outer ring fire, and the fire in the center is called inner ring fire. If there is yellow flame or flame separation, we need to adjust the size of the air door of the stove. First, hold the stove by hand, and there are two handle shaped iron plates called air door regulators at the connection between the burner and the nozzle, as shown in the figure below

second, if there is yellow flame or flame separation in the center fire, we need to adjust the iron plates referred to in the figure below to make the flame normal

then press the opening and move the iron plate up and down to adjust the size of the air inlet, so as to change the state of the flame until it turns into a blue fireworks

third, if the outer ring fire has yellow flame or flame separation, we need to adjust the position indicated by the fingers in the figure below

move the iron plate up and down according to the upper direction of the opening to adjust the size of the air inlet, so as to change the state of the flame until the flame color is normal

when the flame color is normal, we can start to enjoy the delicious life in the kitchen

summary: after reading so much about the installation process of gas stoves, I don't know whether you have mastered it. In fact, the installation of gas stoves is not difficult. If it is the first operation, there may be some small problems. You should also note that when adjusting the firepower, sometimes it is normal for the flame to be mixed with a little yellow flame, which may be the result of the mixing of other substances in the gas or the influence of the surrounding temperature and humidity during combustion, These are normal phenomena

天津男科医院

天津性病医院

唐山男科医院

Copyright © 2011 JIN SHI